Caused By Slow Computer Hard Disk
Computers which originally was normal, after use a few months turned out to be slow. After the check was caused by a hard disk.
Solution:
Hard disk management can cause the computer to be slow.
- Check the hard disk capacity is still a lot of empty or nearly full. To check all the drives on your hard disk follow these steps. Open the Control Panel> Administrative Tools> click Computer Management.
- Computer Management window open> select Storage> select Disk Management. All drives can be seen how much capacity is still empty and still in use.
- If the hard disk capacity has begun to fully do the cleaning the hard disk (disk cleanup).
- Still from the Computer Management window> select the drive yangakan cleared> right click> Properties. Properties window pops up drive> select the General tab> click Disk Cleanup. Wait a few moments after that will appear the windows Disk Cleanup. Check the files that are not needed so that the delete by the system. Click Ok.
- If your hard disk is still full, then you need to remove the files or install programs that are not used / needed.
Order files can cause irregular arrangement of the hard disk into a mess.
To tidy do defrag your hard disk.
Steps are as follows:
- Go to Computer Managemant > Storage > Disk Defragment > select the drive you want to defrag > Defragment.
Errors that occur on your hard disk.
To view and fix hard disk errors can use the following steps:
- Right-click the drive in question > Properties > select the Tools Tab > Check Now.
- Enable the option and then click Start.
Uninstalling stubborn Flashdisk
The flash is over used and will be removed from the computer system. It was removed from the tray icon but still refused to come out.
Solution:
- Make sure that no files from the flash that is run or the process associated with the flash is running. You can go into the windows task manager to make sure by pressing the key combination Ctrl + Alt + Del. On the Application tab locate the file from the flash that is running, after See you select the file and click End Task.
- On the Processes tab make sure there is no process associated with the flash is running. If there is a select process and click End Process.
- Try via Windows Explorer > Right click the drive in question > Eject.
Ikon Removable Hardware Not Appear in System Tray
You want to let go of the flash, external hard disk connected via USB port. Apparently there is no remove hardware icon system tray.
Solution:
- Run Windows Explorer> right-click the hardware in question> Eject.
- If you kurangpuas and want to find the Safety Remove Hardware then the following steps: Run the windows explorer> right click the hardware in question> Properties.
- Appears properties window and then select the Hardware tab select the hardware in question> Properties.
- Appears window Device Properties> Policies tab> click the Safely Remove Hardware.
- After the Safely Remove Hardware window appears> select the hardware that is> click Stop.
Always On Time Computer System Changed
This case was caused by the CMOS battery is discharged. Therefore replace the CMOS battery with new ones. CMOS battery can be found at computer stores.
Long Beep Beep 1 Time
After pressing the power button long audible beep 1 time. Computers do not want to go into the operating system.
Solution:
- Turn off the computer and disconnect the electric current to the computer.
- Beep a long time because there is a problem in memory.
- Beep Beep and the error code depends on the model used by the motherboard bios. Remove the memory card from its slot, then clean the brass plate in memory.
- Clean up all the memory slots with a soft brush.
- Replace the memory card into its slot correctly.
- If you can not try a memory card plugged into another slot.
- Make sure the memory card in good condition, it can be tried by installing a memory card into another computer that has the same slot. If the memory is turned off, with a new.
Beep Beep 1-Short Length and 3 Times
After pressing the power button audible beeps 1 time and 3 times the length short. Computers do not want to go into the operating system.
Solution:
- Turn off the computer and disconnect the electric current to the computer.
- Beep I times and 3 times the length of the short is because there is a problem in the graphics card. Beep beep and an error code depending on the model used by the motherboard bios.
- Remove the graphics card (VGA card) from its slot, then wipe the graphics card with a soft brush and also clean the brass plate.
- Clean up all graphics slots use a fine brush. Replace the graphics card into its slot correctly.
- Make sure your graphics card in good condition, it can be tried by installing a graphics card into another computer that has the same slot.
- If the graphics card was dead, replace with new.
0 komentar:
Posting Komentar